Shop Categories

 [email protected]
Search
View Cart
Checkout

The following NSE6_FWF-6.4 questions are part of our Fortinet NSE6_FWF-6.4 real exam questions full version. There are 35 in our NSE6_FWF-6.4 full version. All of our NSE6_FWF-6.4 real exam questions can guarantee you success in the first attempt. If you fail NSE6_FWF-6.4 exam with our Fortinet NSE6_FWF-6.4 real exam questions, you will get full payment fee refund. Want to practice and study full verion of NSE6_FWF-6.4 real exam questions? Go now!

 Get NSE6_FWF-6.4 Full Version

Fortinet NSE6_FWF-6.4 Exam Actual Questions

The questions for NSE6_FWF-6.4 were last updated on Feb 21,2025 .

Viewing page 1 out of 1 pages.

Viewing questions 1 out of 8 questions

Question#1

Refer to the exhibits.
Exhibit A



Exhibit B



Exhibit C



A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and Io devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?

A. Increase the transmission power of the AP radios
B. Enable frequency handoff on the AP to band steer clients
C. Reduce the number of wireless networks being broadcast by the AP
D. Install another AP in the reception area to improve available bandwidth

Question#2

Refer to the exhibits.
Exhibit A



Exhibit B



A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)

A. For both interfaces in the wtp-profile, configure set vaps to be “Authors”
B. Disable intra-vap-privacy for the Authors vap-wireless network
C. For both interfaces in the wtp-profile, configure vap-all to be manual
D. Increase the transmission power of the AP radio interfaces

Question#3

Where in the controller interface can you find a wireless client’s upstream and downstream link rates?

A. On the AP CLI, using the cw_diag ksta command
B. On the controller CLI, using the diag wireless-controller wlac -d sta command
C. On the AP CLI, using the cw_diag -d sta command
D. On the controller CLI, using the WiFi Client monitor

Question#4

Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)

A. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
B. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the A
C. DARRP measurements can be scheduled to occur at specific times.
D. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.

Explanation:
DARRP (Distributed Automatic Radio Resource Provisioning) technology ensures the wireless infrastructure is always optimized to deliver maximum performance. Fortinet APs enabled with this advanced feature continuously monitor the RF environment for interference, noise and signals from neighboring APs, enabling the FortiGate WLAN Controller to determine the optimal RF power levels for each AP on the network. When a new AP is provisioned, DARRP also ensures that it chooses the optimal channel, without administrator intervention.
Reference: http://www.corex.at/Produktinfos/FortiOS_Wireless.pdf

Question#5

You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?

A. Enable Locate WiFi clients when not connected in the relevant AP profiles.
B. Enable Monitor channel utilization on the relevant AP profiles.
C. Ensure that all allowed channels are enabled for the AP radios.
D. Enable Radio resource provisioning on the relevant AP profiles.

Explanation:
The ARRP (Automatic Radio Resource Provisioning) profile improves upon DARRP (Distributed Automatic Radio Resource Provisioning) by allowing more factors to be considered to optimize channel selection among FortiAPs. DARRP uses the neighbor APs channels and signal strength collected from the background scan for channel selection.
Reference: https://docs.fortinet.com/document/fortigate/6.4.0/new-features/228374/add-arrp-profile-for-wireless-controller-6-4-2

Exam Code: NSE6_FWF-6.4Q & A: 35 Q&AsUpdated:  Feb 21,2025

 Get NSE6_FWF-6.4 Full Version
 About NSE6_FWF-6.4 Questions

TOP Exams